Factory outlets Shaw into 13,911,815,451 

 EC2000 polymer waterproof mortar 
 Product Features: 
 ● Waterproof: to do the bathroom, bathroom, basement, and reservoir water layer, nontoxic. 
 ● anti-corrosion: corrosion as a corrosive gas plant concrete structures maintenance. 
 ● flexible paste: paste can be used for hot and cold on the larger temperature changes, situations or changes in grass-roots tiles, mosaics, marble and so on. Can also be used to paste polystyrene board. 
 ● Smooth plaster polystyrene board, copper, aluminum, ceramic tile surface smooth grass-roots level: Can be used for plastering construction. Can also do the walls, ceiling insulation layer benzene board Overlay plaster. 
 ● repair: the repair of the coagulation and cellular vulnerability, cracks, protective layer damage, leakage of tendons and other defects. 
 Technical performance: 
 Hand side of the polystyrene board paste performance: 
 Pursuant to DBJ01-63-2002 <> 
 Inspection of the project performance indicators? Test results 
 Tensile bond strength (Mpa) mortar at room temperature of a polystyrene board ≥ 0.10 and poly destruction 0.11, polyphenylene destruction 
 Water resistance ≥ 0.10, and poly destruction 0.11, polyphenylene destruction 
 Freeze-thaw resistance ≥ 0.10, and poly destruction 0.11, polyphenylene destruction 
 Operational time, h ≥ 2 2.5 
 Flexibility (28d creased ratio) ≤ 3 2.8 
 24H of water absorption, g/m3 ≤ 1000 525 
 Permeable (24h), ml ≤ 3 
 Crack resistance 5mm No crack No crack 

 2, the base surface of the concrete and other physical and mechanical properties 
 Project performance indicators 
 (Mpa) 28 days, compressive strength of 24 Mpa 
 Flexural strength (Mpa) 28 days 9.5 Mpa 
 Tensile strength (Mpa) 28 days 4.8-5.0 Mpa 
 Elastic modulus of 7.9 × 103-9.7 × 103 
 Tensile bond strength (Mpa) mortar - mortar at room temperature normal ≥ 0.70 
 Water resistance ≥ 0.50 
 Temperature ≥ 0.50 
 Freeze-thaw resistance ≥ 0.50 
 Water absorption 2.8% 
 Impermeability of 0.6-1.4Mpa 
 Frost resistance of -30 ℃ 18h soaking 6h, 40 cycles, without exception, compressive strength decreased by 4% 
 Bending resistance of 100 × 500 × 400mm polystyrene board wipe 3mm polymer mortar cured for 28 days under 400mm bending moment, bending 120 degrees without cracking 
 The first test dry and crack resistance in the 250 × 250 × 50mm aerated concrete rubbed 3mm polymer mortar, immediately placed under 3m / s (air temperature 30 ℃) dry 6h without cracking 

 How to construction? 
 ● base surface requirements: clean and free of oil drifting loose animals, and spray the right amount of water, wet and Mingshui. 
 Materials: first EC2000 glue into the bucket, then slowly add the EC2000 powder, mechanical agitation or low-speed stirrer and stir until evenly without caking, stir together the paint should be used up within 2-3 hours, the temperature higher, mixing good mortar, no more than 5% of the total amount of water added. 
 ● Concrete repair Construction 
 Repair of concrete in the repair parts required wiping 3-5mm thick or required by the thickness of the polymer mortar. 
 Amount of reference: press 3-5mm thickness calculation per square meter will take about 3-4Kg. 
 ● insulation overlay construction 
 First, mixing a good polymer mortar, wipe the surface of the polystyrene board thickness 2-3mm, and then paving the alkali-resistant fiberglass mesh cloth, the cloth is pressed into the mortar and leveling, fiberglass lap width of 5 - 10mm, fiberglass cloth must be completely buried, not wrinkled, not pressed into the deep; Finally, the bottom surface mortar solidification front add a touch of the surface layer of polymer mortar, thickness 1-2mm plaster reinforcement layer total thickness of 3-5mm . 
 Amount of reference: the amount of rubber 0.35KG/2.0mm about the powder dosage 1.4kg/2.mm about. 
 ● Construction of waterproof layer 
 Evenly with a spatula Scratch the first pass, 5 scratch-eight hours after the second time, to avoid the eye of a needle, please facade plane crossed scratch. To ensure effective waterproof. Scratch at least twice the coating. (Note: coating drying time and temperature and air relative humidity, For pavement to wait after the coating is completely dry before proceeding) 
 Amount of reference: Scratch two times per square meter takes about 2-2.5KG. 
 Storage: 
 Engineering Packaging: EC2000 glue: 50KG / barrel; the EC2000 powder: 50KG / barrel. 
 ● should be kept dry, unopened shelf life of six months, the rubber a year.